Boris,
I love everything about it except the blade. :) That triangular ricasso isn't something that's usually seen historically. The hilt work is beautiful.

I personally love the lines of the blade. Not a replica of an existing piece, but a beautiful stand-alone dagger. Bravo!...........McM

# Chad
I absolutely agree with you.
But as mentioned, the blade was made in 2008, when I my knowledge was inferior - and this is the result from this.
Since then, I've seen many rondel daggers - both historical and very well-made high-quality replicas. If I have to make another such dagger now (or in the future), it will be quite different and far more precise.

BTW, I have just some very scarce memories of how I made the blade :confused: ;)
I only remember perfect sanding up to grit #400 before the heat-treatment :wtf: (there was no one to tell me it's absolutely un-necessary); and the couple of hours of hard labour to clean the oxidation after the heat-treatment with grit #400 again :eek: :\

For the scabbard of this dagger I chose classical leather wrapped wooden core, instead of more historically precise leather one.

The work followed the same steps as the scabbard of the Type XVa sword, the wood is beech again - actually some remnants from the sword.
Two halves marked and cut into shape

[ Linked Image ]

And both chiseled

[ Linked Image ]

As I was under an impression that some forum-mates were interested in the "wooden sticks trick", I would like to show the whole process step by step with appropriate images.

Here we go:
* take one of the planks and mark where the holes will be

[ Linked Image ]

You need a pair near the mouth, a single hole at the point and another or two pairs distributed evenly between them. As this scabbard is short, I have a pair at the mouth, another at the point, and a third somewhere in the middle.

** drill the holes on the contact surface

[ Linked Image ]

I use 1.8 mm drill-bit. Also, I found it better to do this on the drill-press - it gives me well-drilled, perpendicular holes.

*** the plank with the holes drilled

[ Linked Image ]

**** match very well both planks (you could use the blade itself too) and clamp them tightly - here just two clamps are enough indeed

[ Linked Image ]

***** remove the blade (if you used it) and drill the other plank THROUGH holes already drilled

[ Linked Image ]

This could be done on the drill-press also, but for me it's better (and easier) to work with a hand-drill

****** now we have both planks with matching holes, drilled on them

[ Linked Image ]

* now it's time to prepare several wooden sticks about an inch long

[ Linked Image ]

Here I used safety-matches sticks, cut in halves with rounded corners

** glue them in the holes of one of the planks

[ Linked Image ]

It's not a bad idea to sharpen the points of the sticks - this will help later. Take several minutes of rest, while the glue is drying; and after that you could make a test-fit (this is purely optional).

[ Linked Image ]

*** apply glue over the contact surface

[ Linked Image ]

**** and insert the sticks protruding from one plank through the holes in the other

[ Linked Image ]

***** press the planks

[ Linked Image ]

****** and using a rubber mallet just hammer the contours of the scabbard lightly, in order to let the excessive glue out

[ Linked Image ]

[ Linked Image ]

******* finally, clamp the core

[ Linked Image ]

The scabbard after some passes over the belt-grinder - this time everything was so fast :surprised: , that I wonder WHY I shaped the Type XVa scabbard with files by hand :?: :wtf:

[ Linked Image ]

As I wanted the front rondel to be partially hidden, I cut an octagon from a piece of plank and glued it at the mouth of the scabbard - thus forming the bottom of the "nest"

[ Linked Image ]

For the walls I used piece of 4 mm thick plywood with inside cut, which repeated the contours of the rondel

[ Linked Image ]

All was glued together, fitted to shape, the corners cut, filed and sanded

[ Linked Image ]

[ Linked Image ]

The chape for this scabbard was made, following the already worked off technology (needs additional sanding and polishing)

[ Linked Image ]

The decorative cut is the same, as the one of the sword scabbard - I had the idea to make both scabbards matching in style. Yes indeed, it would look like that the owner had ordered the weapons at different masters, while the scabbards had been made by one.
Two views of the scabbard with the chape

[ Linked Image ]

[ Linked Image ]

And the dagger in

[ Linked Image ]

and out of it

[ Linked Image ]

As clearly seen, the scabbard is quite longer from the blade. As I have the PoB at the front surface of the front rondel, I have to make it longer with massive chape, in order to get the PoB as forward as possible.

Some progress with the leather wrapping:

* all the raisers plus the "nest" glued

[ Linked Image ]

** the "nest" at the front

[ Linked Image ]

*** and at the mouth

[ Linked Image ]

**** finally - the dagger in the scabbard

[ Linked Image ]

Some proggress with the scabbard made recently.

The chape sanded and polished

[ Linked Image ]

and the leather wrapped, the chape glued

[ Linked Image ]

[ Linked Image ]

Actually, this was the second (and the final) wrapping
The first one was made with other leather (I had some pieces I wanted to get rid off), but this leather wasn't the best choice. During waxing it showed some very strong tendency to shrink while heated and I stripped it from the scabbard, replacing with already tested leather - the same I made the wrapping of the sword scabbard with.

And with this post, the rondel-dagger is actually completed

The leather strap for the belt - the colour is extremely dark "bordeaux" (wine-red colour), due to combined effect of the oil and wax

[ Linked Image ]

And the strap attached to the scabbard.

[ Linked Image ]

I did this by wrapping two cords (running paralel each other) around the scabbard and the strap. As there is no any glue or adhesive, I rely only on the friction and tight wrap.

[ Linked Image ]

[ Linked Image ]

I'm not sure if this would be permanent or temporary finish. As a whole, I'm not quite well satisfied by the result and it's possible to change it someday. The only thing that boders me is the fact that many things made as temporary, usually get to be permanent :\

And the dagger in the scabbard

[ Linked Image ]

[ Linked Image ]

Very soon I'll provide more and better images of the finished set.

A trick I've used in the past....

Looking at this photo:

[ Linked Image ]

At the very BASE of your leather strap, just past the cord wrapping.... consider adding a stitched "extra piece" of leather - it will act as a wedge, absolutely preventing the strap from coming out from under the cord wrap - even under great stress.

Gorgeous!
Thanks for this idea.

The finished piece

[ Linked Image ]

[ Linked Image ]

[ Linked Image ]

[ Linked Image ]

[ Linked Image ]

[ Linked Image ]

And some more

[ Linked Image ]

[ Linked Image ]

[ Linked Image ]

[ Linked Image ]

[ Linked Image ]

[ Linked Image ]

Stunning result! I'm not big on rondels, but that is very nice - I love how you recessed the flower petals, and also the 'nest' on the sheath!

Well, that finishes this project!

I would be glad to read your comments.
And please, feel absolutely free to criticize me, especially on the technical issues.

That is a lovely job - as you always do :).

Beautiful stuff! It's probably a bit late now, but i was thinking the pommel would look rather fetching if the flower design was enameled.

Are you going to take a picture of the rondel and the type XV together?